View PCSOOV_8511436.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

prepared by: date: shar electronic components group sharp corporation specification i -+=%an opto-electronic devi f device specification for photocoupler i model no. PCSOOV (businessdealingname: pc9oovonszxl 1. these specification sheets include materfals protected under copyright of sharp corporation (?sharp?). please do not reproduce or cause anyone to reproduce them without sharp?s consent. - 2. when using this product, please observe the absolute maximum ratings and the instructions for use outlined in these specification sheets, as well as the precautions mentioned below. sharp assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets, and the precautions menttoned below. (precautions) (1) this product is designed for use in the following application areas ; i l oa equipment * audio visual equipment * home appliances - telecommunication equipment (terminal) * measuring equipment * tooling machines - computers 1 if the use of the product in the above application areas is for equipment listed in paragraphs (2) or (3). please be sure to observe the precautions gtven in those respective paragraphs. (2) appropriate measures, such as fail-safe design and redundant design considering the safety design of the overall system and equipment, should be taken to ensure reliability and safety when this product is used for equipment which demands high reliability and safety in function and precision, such as ; [ * transportation control and safety equipment (aircraft, train. automobile etc.) - traffic sigmk * gas leakage sensor breakers * rescue and security equipment * other safety equipment i [3) please do not use this product for equipment which require extremely high reliability and safety in function and precision, such as : [ * space equipment * telecommunication equipment (for trunk lines) l nuclear power control equipment * medical equipment 1 (4) please contact and consult with a sharp sales representative if there are any questions regarding interpretation of the above three paragraphs. 3. please contact and consult with a sharp sales representative for any questions about this product. customer?s approval date by date f j-p. ij, ,+a-3 presented j by /g&?&&h k. hachimura, department general manager of engineering dept. .i1 opto-electronic devices div. elecom group sharp corporation
shrrp corporati 1. application on this specification applies to the outline and characteristics of photocoupler model no. PCSOOV. 2. outline refer to the attached sheet. page 3. 3. ratings and characteristics refer to the attached sheet, page 3 to 5. 4. reliability refer to the attached sheet, page 8. 5. outgoing inspection refer to the attached sheet. page 9. 6. supplement 6.1 isolation voltage shall be measured in the following method. (i) short among pins 1 to 3 on the primary side and among pins 4 to 6 on the secondary side. (2) the dielectric withstand tester with zero-cross circuit shall be used. (3) the wave form of applied voltage shall be a sine wave. (it is recommended that the isolation voltage be measured in insulation oil.) 6.2 the business dealing name used for this product when ordered or delivered shall be PCSOOVonszx. 6.3 package specifications refer to the attached sheets-2- 1 to 2-3.
sharp corporation 6.4 ul : under preparation 6.5 theory of operation (1) when the forward current of above the ?h+l? threshold input current (ir,.j is applied to the input side, the output will go ?low level?. (2) when the forward current on the input side goes below the ?l+h? threshold input current (i,,,) is applied to the input side, the output will go ?high level?. 6.6 this product is not designed against irradiation. this product is assembled with electrical input and output. - this product incorporates non-coherent light emitting,diode. 6.7 ods materials this product shall not contain the following materials. also, the following materials shall not be used in the production process for this product. materials for ods : cfc, halon, carbon tetrachloride. 1.1.1 -trichloroethane (methylchloroform) 6.8 brominated flame retardants specific brominated flame retardants such as the pbbos and pbb, are not used in this device at all. 7. notes refer to the attached sheet-l- 1. 2.
sharp corporation 2. outline anode inai 7.12zto.3 - m ?i m cd - regulator anode cathode n. c pin nos. and inter!?ial connection diagram \ lot no. ?1 7.629~0.3 l l 2.54&o. 25 0.5fo. 1 *l) 2-digit number shall be marked according to din standard. *2) marking is laser marking unit: l/l mm product mass : approx. 0.36g name PCSOOV outline dimensions (business dealing name : pc9oovonszx)
sharp corporfltion ratings and characteristics 3.1 absolute maximum ratings *l the derating factors of absolute maximum ratings due to ambient temperature are shown in fig. 1, 2. 3. *2 pulse widths 100 ps, dutyratio : 0.001 *3 ac for 1 min, 40 to 6o%rh *4 forlos
sharp corporation 3.2 electra-optical characteristics parameter forward voltage reverse current terminal capacitance operating supply voltage range low level output voltage high level output current low level supply current high level supply current ?h-l? threshold input current *l ?l-h? threshold input current *2 hysteresis *3 isolation resistance ?h-l? propagation time ?l-h? propagation time fall time rise time -gin. 1 typ. 1 max. 1 unit 1 -? conditions ir i - 1 - 1 10 1 pa 1 ta=25%, v,=3v ct ( - i30 1250 1 ,,(~;25;,v=o vcc 131 -1151vi _ vol 1 - 1 0.2 1 0.4 1 v 1 ~&6!&na,vcc=5? bh 1 - 1 - 1 100 1 pa 1 g$=l5v bcl 1 - 1 2.5 1 5.0 1 ma 1 vcc=5v, 1,=4ma e ch i - 1 1.0 1 5.0 1 ma 1 vcc=5?, i,=oma ?flh /if,, 1 0.5 1 0.7 1 0.9 1 - 1 vcc=5v, iq=280q rho i5xlo?ol 10? 1 - 1 r ( t$..~ox$oov tphl t plh tf tr 1 3 2 6 - 0.05 0.5 0.1 0.5 ta=25% vcc=5v. 1,=4ma r,=280 0
shflrp corporation *1 i,, represents forward current when output goes from ?h? to ?l?. ? ?flh represents forward current when output goes from ?l? to ?h?. ?3 hysteresis : iflh/ifhl *4 test circuit for response time shall be shown below. tr==tt-0.0 .?0=50n vobge regulator output test circuit diaffram timing chart
sharp corporation (fig. 1) forward current vs. (fig. 2) output powe ambient temperature vs. ambient temperature?- ! -50 $ 2 40 z g 30 2 3 20 2 g 10 0 -25 0 25 50 7585 100 125 -25 0 25 50 7585 100 125 ambient temperature ta (?c) ambient temperature ta (?c) $ g 8 250 b 3 100 ?a x 50 5 0 0 5 e tz 200 13 170 g 150 3 2 ?el b 100 3 ifi 50 (fig. 3) total power dissipation vs. ambient temperature -25 0 25 50 7585 100 125 ambient temperature ta (?c)
sharp corpor~ition 4. reliability the reliability of products shall be - satisfied with items listed below. confidence level : 90% ltpd : 10%/20% test items test conditions failure judgement samples in) ?1 criteria defective(c) solderability *2 230%. 5 s n=ll, c=o soldering heat 260%. 10 s v,>ux 1.2 n=ll. c=o terminal strength weight : 5n i,>ux2 n=ll. c=o (tension) 5 s/each terminal vo,>ux1.2 - r terminal strength weight : 2.5n n=ll, c=o (bending) *3 2 times/each terminal i,,>ux1.2 mechanical shock 15km/s?, 0.5ms iccl>ux 1.2 n=ll, c=o 3 times/fx. +-y, fz direction i cch>ux 1.2 variable frequency 100 to 2000 to loohz/4min vibration 200m/sz i,,,>ux1.3 n=ll. c=o 4 times/ x. y. z direction i,, sharp corpomtion 5. outgoing inspection 5.1 inspection items (1) electrical characteristics v, i,. v,,. &. icc/ icch? i,,. iiqj+. rise. visa (2) appearance 5.2 sampling method and inspection level a single sampling plan. normal inspection level ii based on is0 2859 is applied. the aql according to the inspection items are shown below. defect inspection item major electrical characteristics defect unreadable marking minor appearance defect except defect the above mentioned. aql wi 0.065 0.25
shflrp corporation 1 for cleaning precautions for photocouplers (1) solvent cleaning : solvent temperature 45% or less immersion for 3 min or less (2) ultrasonic cleaning : the effect to device by ultrasonic cleaning differs by cleaning bath size, ultrasonic power output, cleaning time, pcb size or device mounting condition etc. please test it in actual using condition and con&n that doesn?t occur any defect before starting the ultrasonic cleaning. (3) applicable solvent : ethyl alcohol, methyl alcohol, isopropyl alcohol in case when the other solvent is used. there are cases that the packaging resin is eroded. please use the other solvent after thorough coniirmation is performed in actual using condition. 2. please use the same as normal integration circuit about static electricity in order that this device is opic photocoupler. 3. in order to stabilize power supply line. we recommend to connect a by-pass capacitor of 0.0 1 p f or more between vcc and gnd near the device. 4. the detector which is used in this device, has parasitic diode between each pins and gnd. there are cases that miss operation or destruction possibly may be occurred if electric potential of any pin becomes below gnd level even for instant. therefore it shall be recommended to design the circuit that electric potential of any pin does not become below gnd level. 5. the led used in the photocoupler generally decreases the light emission power by operation. in case of long operation time, please design the circuit with considering the decreases of the light emission power of the led. (500/6/5years) please decide the input current which become 2 times of max. i,,,
sharp corporation 6. precautions for soldering photocouplers (1) in case of soldering to lead 260% 10 s or less 180 160 140 an example of device temperature vs. soldering time *- e-- *- -0 120 - .*- ed device .# temperature go - (cl solder 20 - 0? ? ? ? 1 i 1 i 0 2 4 6 8 10 12 14 16 18 20 soldering time (s) (2) if solder reflow : it is recommended that only one soldering be done at the temperature and the time within the temperature profile as shown in the figure below. 230c 18oc 25c (3) other precautions an infrared lamp used to heat up for soldering may cause a localized temperature rise in the resin. so keep the package temperature within that specified in item (2). also avoid immersing the resin part in the solder.
shflrp corporation package specification 1 package materials no. name 1 sleeve materials plastfcs with preventing static electricity purposes products packaged 2 stopper rubber products tied 3 packing case corrugated cardboard sleeve packaged 4 kraft tape paper lid of packaged case fixed - model no., quantity, 5 label paper inspection date and lot no. specified 2 package method (1) max. 5opcs. of products shall be packaged in a sleeve and both of sleeve edges shah be fixed by stoppers. (2) max. 20 sleeves above shall be packaged in a packing case and pack a sheet of cushion at one side. (3) model no., quantity, inspection date and lot no. shall be marked on the label and this label shall be put on the side of the packaging case. (4) case shall be closed with the lid and enclosed with kraft tape. 3 package outline dimensions (1) sleeve outline dimensions refer to the attached sheets-2-2. (2) packaging case outline dimensions refer to the attached sheets-2-3.
sharp corporation 6.7 4 length : l=520 f 2mm note 1) thickness : 0.5k0.2mm 2) outer r: 0.5mm 3) process with applying antistatic agent. 4) unless otherwise specified tolerances shall be f0.5mm. (however except for deformation due to the rubber stopper in sleeve.) unit : l/ lmm name sleeve outline dimensions
shmip corporrtion sleeve anode mark or \ arranged at stopper side wthout pulled potion. /stopper mwlout pulled portlon) (with pulled portion) -a- 20 sleev& (5lines x4sta.m *max. m it is impossible to mix erent model or different i i i i diffi rank model in one case. kraft tape label unit: l/lmm name packing case outline dimensions

▲Up To Search▲

Price & Availability of PCSOOV

	To Download PCSOOV Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .